Difference between revisions of "Networking vserver guests RHEL"
From Linux-VServer
m (New page: ==Public IP Space== ==Chose a private IP range== Private IP Range: 192.168.1.0<br> Host Private IP: 192.168.1.1<br> Guest Private IP: 192.168.1.2<br> ==network-scripts== In a RHEL based ...) |
|||
Line 1: | Line 1: | ||
==Public IP Space== | ==Public IP Space== | ||
− | + | 5.5.5.5 | |
==Chose a private IP range== | ==Chose a private IP range== | ||
Private IP Range: 192.168.1.0<br> | Private IP Range: 192.168.1.0<br> | ||
Line 26: | Line 26: | ||
<pre> | <pre> | ||
ifup eth0:1 | ifup eth0:1 | ||
+ | </pre> | ||
+ | |||
+ | Assuming your vserver is test01 | ||
+ | <pre> | ||
+ | echo "eth0:1" > /etc/vservers/test01/interfaces/0/dev/ | ||
+ | echo "192.168.1.2" > /etc/vservers/test01/interfaces/0/ip | ||
+ | echo "255.255.255.0" > /etc/vservers/test01/interfaces/0/mask | ||
+ | </pre> | ||
+ | |||
+ | Now your guest should have outbound connectivity. | ||
+ | |||
+ | <pre> | ||
+ | [root@34 ~]# vserver test01 enter | ||
+ | bash-3.1# ifconfig | ||
+ | eth0 Link encap:Ethernet HWaddr 00:0E:0C:69:ED:E0 | ||
+ | inet addr:10.10.10.2 Bcast:10.10.10.255 Mask:255.255.255.0 | ||
+ | ... | ||
+ | bash-3.1# ping www.google.com | ||
+ | PING www.l.google.com (74.125.45.99) 56(84) bytes of data. | ||
+ | 64 bytes from yx-in-f99.google.com (74.125.45.99): icmp_seq=1 ttl=244 time=22.3 ms | ||
+ | 64 bytes from yx-in-f99.google.com (74.125.45.99): icmp_seq=2 ttl=244 time=22.5 ms | ||
+ | </pre> | ||
+ | |||
+ | ==Inbound Connections and NAT== | ||
+ | Now we have to establish inbound connectivity. This can be done with Network Address Translation. We can expose the SSH service through NAT. | ||
+ | |||
+ | <pre> | ||
+ | 5.5.5.5:9000->192.168.1.2:22 | ||
</pre> | </pre> |
Revision as of 02:17, 7 May 2008
Contents |
Public IP Space
5.5.5.5
Chose a private IP range
Private IP Range: 192.168.1.0
Host Private IP: 192.168.1.1
Guest Private IP: 192.168.1.2
network-scripts
In a RHEL based system many configurations are stored in /etc/sysconfig. The network settings are /etc/sysconfig/network-scripts.
cp /etc/sysconfig/network-scripts/ifcfg-eth0 /etc/sysconfig/network-scripts/ifcfg-eth0:1 vi /etc/sysconfig/network-scripts/ifcfg-eth0:1
DEVICE=eth0:1 HWADDR=00:0e:0c:69:ed:e0 ONBOOT=yes NETMASK=255.255.255.0 IPADDR=192.168.1.1 TYPE=Ethernet
This IP address will now start at boot up.
ifup eth0:1
Assuming your vserver is test01
echo "eth0:1" > /etc/vservers/test01/interfaces/0/dev/ echo "192.168.1.2" > /etc/vservers/test01/interfaces/0/ip echo "255.255.255.0" > /etc/vservers/test01/interfaces/0/mask
Now your guest should have outbound connectivity.
[root@34 ~]# vserver test01 enter bash-3.1# ifconfig eth0 Link encap:Ethernet HWaddr 00:0E:0C:69:ED:E0 inet addr:10.10.10.2 Bcast:10.10.10.255 Mask:255.255.255.0 ... bash-3.1# ping www.google.com PING www.l.google.com (74.125.45.99) 56(84) bytes of data. 64 bytes from yx-in-f99.google.com (74.125.45.99): icmp_seq=1 ttl=244 time=22.3 ms 64 bytes from yx-in-f99.google.com (74.125.45.99): icmp_seq=2 ttl=244 time=22.5 ms
Inbound Connections and NAT
Now we have to establish inbound connectivity. This can be done with Network Address Translation. We can expose the SSH service through NAT.
5.5.5.5:9000->192.168.1.2:22